Product
Ingersoll Rand 54672530 Air Filter Element for N55/N75 Screw Compressors
Genuine Ingersoll Rand 54672530 air filter element for N55 and N75 screw compressors. 247 mm OD, 365 mm height, 5–10 μm filtration, low resistance and high dust-holding capacity. Cross-reference SA17281; serial-number matching available.
- Export packaging & documentation support
- OEM / ODM customization available
- Sample and bulk order workflow
Product Overview
54672530 is a genuine Ingersoll Rand intake air filter element built for N55 and N75 series screw air compressors. The pleated synthetic fiber/glass fiber media captures airborne dust and particulate before it reaches the airend, helping protect rotors, bearings and shaft seals while supporting stable compressor performance and service life.
This large cylindrical element measures approximately 247 mm outside diameter and 365 mm overall height, with a red polyurethane end-cap gasket for positive sealing. It is a direct fit for the N55/N75 intake housing and cross-references HiFi Filter SA17281. Several Atlas Copco part numbers are also listed as compatible references below.
Key Specifications
- Part number: 54672530
- Brand: Ingersoll Rand
- Component: Air filter element / intake filter
- Machine compatibility: N55, N75 screw compressors
- Cross-reference: HiFi SA 17281
- Outside diameter: 247 mm
- Inside diameter: 150 mm
- Overall height: 365 mm
- Weight: approx. 5 kg
- Filtration rating: 5–10 μm
- Filtration efficiency: approx. 99% @ 10 μm
- Filter class: F7–F8 (EN 779 / ISO 16890)
- Dust-holding capacity: approx. 1.0–1.5 kg
- Beta ratio: β₁₀ ≥ 1000
- Rated air flow: approx. 10–13 Nm³/min (for 55–75 kW machines)
- Initial pressure drop: approx. 250–350 Pa at rated flow, clean
- Operating differential pressure: 350–600 Pa
- Alarm / final resistance: 700 Pa alarm; 900 Pa final (replace immediately)
- Media: synthetic fiber / glass fiber, yellow pleated paper
- Media weight: approx. 120–150 g/m²
- Support: galvanized expanded metal mesh, inner and outer
- End cap: red polyurethane (PU)
- Seal: red nitrile rubber (NBR), top and bottom
- Operating temperature: −20 °C to 80 °C continuous; up to 100 °C short-term
- Relative humidity: ≤95% RH, non-condensing
- Collapse pressure resistance: ≥4.0 kPa
- Service life: approx. 4,000 hours (8–12 months) under standard conditions; 2,000–3,000 hours in high-dust environments
- Shelf life: 36 months in original sealed packaging, dry ambient conditions
Standards and Test References
- ISO 5011 — inlet air filter performance testing for internal combustion engines and compressors
- ISO 16890 / EN 779 — general ventilation air filter classification
- GB/T 14295 — air filters
- GB/T 6165 — test methods for air filter performance
Installation and Maintenance
Replacement interval: every 4,000 hours or 8–12 months under standard conditions, whichever comes first. In high-dust environments, shorten to 2,000–3,000 hours. Replace immediately if the media is visibly darkened or heavily loaded, or if differential pressure reaches 900 Pa.
- Lock out / tag out: switch off the main power and confirm the machine has fully stopped.
- Open the filter housing: release the bolts or clamps and remove the cover.
- Remove the old element: pull out the used 54672530 element and check whether the old gasket remains in the housing groove.
- Clean the housing: wipe the inner wall and sealing face with a clean cloth to remove dust and debris.
- Inspect the new element: verify part number 54672530, and check media, end caps and red seal for damage or aging.
- Install: seat the new element vertically in the housing center; confirm both seals contact correctly with no misalignment.
- Refit the cover: reinstall and tighten bolts or clamps evenly.
- Start-up check: run the compressor and listen for air leakage at the filter housing.
Buyer FAQ
Is 54672530 a genuine Ingersoll Rand part?
Yes. 54672530 is a genuine Ingersoll Rand replacement element with yellow high-efficiency media and a red polyurethane end-cap seal, specified for N55/N75 screw compressors.
Which machines does it fit?
Ingersoll Rand N55 and N75 series screw compressors. If you are unsure, provide the machine serial number and we will confirm the correct item.
What is the cross-reference?
HiFi Filter SA 17281. Compatible Atlas Copco references include 1613950100, 1613951000, 1631043700 and 2255300129.
What are the dimensions?
Approx. 247 mm outside diameter, 150 mm inside diameter, 365 mm overall height, approx. 5 kg.
How do I know when to replace it?
Replace when the media is visibly dark or heavily loaded, when differential pressure reaches the 700 Pa alarm point, or when the 4,000-hour / 8–12-month interval is reached.
Compatible Machines and Related Parts
- N series: N55, N75
Related part numbers for reference:
- SA 17281 — HiFi air filter element (cross-reference for 54672530)
- 1613950100 — Atlas Copco air filter element (compatible reference)
- 1613951000 — Atlas Copco air filter element (compatible reference)
- 1631043700 — Atlas Copco air filter element (compatible reference)
- 2255300129 — Atlas Copco air filter element (compatible reference)
- 88111901 — air filter element for SSR M37/M45 machines
Ordering and Export Support
For distributors and service providers, we supply this filter element under standard export packing and can discuss OEM/ODM labelling and distributor OEM packing arrangements. To confirm fitment and current availability, send us the compressor serial number — we will verify against the parts diagram and return a quotation, datasheet and packing details.